BaseEdge Pro · Baseedge angle meter
Ski & snowboard
base edge
measured to 0.01°.
Electronic dial gauge, hairline straightedge and LED light gap in one instrument. The BaseEdge Pro determines the exact actual baseedge angle of skis and snowboards.
- Resolution
- 0.01°
- Resolution
- Light gap
- LED
- Light gap
- Battery
- Mobile
- Battery

Why measure
0.5° or 1.0°? A difference you feel on ice straight away.
The base bevel defines the ski’s responsiveness and the exact point at which the edge engages. A few tenths of a degree decide between aggressive edge bite and forgiving, drift-friendly behaviour. If you don’t measure this angle precisely, you leave the setup to pure chance.
Base bevel and ski behaviour
- 0.30°–0.50°: very direct
- 0.50°–0.75°: sporty
- 0.75°–1.00°: forgiving
- 1.00°–1.30°: delayed
Please note: these are guide values – the right angle depends on the athlete and on how the side edge is ground. Everyone finds their own combination over time. That makes it all the more important to know it exactly and to hit it again reliably at every service.
Where does the demo ski sit? Try it in the live demo
Too much is too much
A base edge bevelled too far cannot simply be filed back – the whole ski has to be ground flat again. Measure before grinding; if a ski turns well, leave its angle as it is.
Spot the differences
The angle can vary between the two edges and along the length of the ski. You can’t see that with the naked eye – the BaseEdge Pro measures it in seconds.
Quality control
Check in seconds after every service whether the target angle was hit – measured, not felt.
The device
Precision you can hold.
Electronic dial gauge, straight edge and LED in one compact device – for the workshop and the race course. Made in Austria.
- Electronic dial gauge
- 0.01 mm resolution, easy to read on the large display.
- Red knurled nut
- Fine-tunes the support until no more light shines through.
- Straight edge with LED
- Reveals even the tiniest light gap at the edge.
- Battery powered
- No cable, no socket – ready to use anywhere.

Live demo
Built for the hundredths.
The light-gap method – try it yourself.
Drag the red knurled nut – or use the slider – until no more LED light passes between straightedge and edge.
Dial gauge in mm · mapping in this demo: 1 mm = 1°. What matters is the light gap above the steel edge; light may still show on the base side.

Large, clear display
Degrees = millimetres – easy to read, in the service workshop or on the side of the slope.
Dial gauge + straightedge
Proven precision instruments, combined in one device.
Built-in LED
Makes even the smallest gap visible – every measurement can be verified by eye.

Knurled nut
Mechanical adjustment via knurled nut – precise and fast.
Battery powered
No cable, no socket. Workshop, ski service or right at the race course.
Safely stowed
Compact hard case with a custom-cut foam insert – the BaseEdge Pro stays protected and is always ready to hand.
- Rugged hard shell
- Custom-cut foam insert
- Handy for workshop and race course


How to use
Four steps to the angle.
- 01
Prepare
Clamp the ski, clean the base and steel edge, and check that the base is flat.
- 02
Calibrate
Place the device across the base, raise the support until only the straightedge rests on it, and zero the dial gauge.

Straightedge flat on the base, marker at the transition to the edge. - 03
Measure
Switch on the LED and turn the knurled nut until no light passes between straightedge and edge.

The device tilts by the base bevel angle – the straightedge sits flush on the edge. - 04
Read
The value in millimetres equals the angle in degrees. Measure at several points for a reliable result.
Who it’s for
Racing
World Cup teams and racers who need a repeatable setup.
Ski service & retail
Workshops that measure before and after grinding instead of guessing.
Clubs & ambitious skiers
Ski clubs, coaches, junior teams and private racers who prepare their own equipment.
Where to buy
Available from our partners.
The BaseEdge Pro is available from selected dealers – online or in store, where you can try the device in person.
FAQ
Frequently asked questions.
Question not answered? Get in touch.
Precisely measure the actual base edge angle, set the grinding machine exactly and verify the target angle flawlessly after the service. For a reproducible high-end setup without compromise.
Enquiry
Measure, don’t guess.
We’ll advise you personally and prepare a non-binding quote – for the workshop or the team.


